Prof. Ir. Hadi Sutanto, M.M.A.E., Ph.D.
04/05/2013 00:00:00
|
|
|
Nama
NIDN
Jabatan Akademik
Jabatan
E-mail:
Kantor
|
: Prof. Ir. Hadi Sutanto, M.M.A.E., Ph.D.
: 0315015603
: Guru Besar
: Guru Besar Teknik Manufaktur
: hadi.sutanto@atmajaya.ac.id
: Gedung Paul Cho (K3) Lantai 2
Program Studi Teknik Mesin, Fakultas Teknik
Universitas Katolik Indonesia Atma Jaya
Jenderal Sudirman 51 Jakarta 12930 Indonesia
Tel.: (021) 570 8826
|
Pendidikan
- S3 - Ph.D. in Manufacturing Technology, Faculty of Mechanical Engineering, Czech Technical University in Prague, Czech Republic (2006)
- S2 - Master of Mechanical & Aerospace Engineering (MMAE), Department of Mechanical and Aerospace Engineering, Illinois institute of Technology (IIT), Chicago, USA (1994)
- S1 - Insinyur (Ir.) Teknik Mesin, Universitas Gadjah Mada, Indonesia (1985)
Bidang Keahlian
Proses Pemesinan, Teknik Produksi & Material
Pengajar Mata Kuliah
- Perancangan Teknik
- Pengukuran Teknik
- Proses Pemesinan
- Proses Pemesinan Non Konvensional
Publikasi Ilmiah
- A. Sunyoto, F. Wenehenubun & H. Sutanto (2013) The effect of number of blades on the performance of H-Darrieus type wind turbine. Quality in Research (QiR) International Symposium on Mechanical and Maritime Engineering 2013, Yogyakarta 25-28 Juni 2013. DOI: 10.1109/QiR.2013.6632563
- Hadi Sutanto (2008) Cutting Forces and Surface Quality in Precision Milling of Hardened Steel with Cubic Boron Nitride Cutting Tools. EIT Journal of Engineering Technology, The Engineering Institute of Thailand under H.M. The King‘s Patronage. Bangkok, Thailand.
- Hadi Sutanto & Jan Madl (2006) Surface Roughness of Hardened Steel in Precision Milling with Ceramic and Cubic Boron Nitride Cutting Tools. Science Report Project PL-007, Modern Metrology in Quality Management Systems, Central European Exchange Program for University Studies (CEEPUS), Kiecle, Poland.
- Hadi Sutanto & Jan Madl (2005) Precision Milling of Hardened Steel using Ceramics and Cubic Boron Nitride Cutting Tools. Journal of Manufacturing Technology, Vol. 10 No. 2, Czech Republic.
- Hadi Sutanto (2005) Some Aspects on Precision Machining of Hardened Steels. Journal of Manufacturing Engineering, Pressov, Slovak, Vol. IV No. 2.
- Erwin Adi Hartono & Hadi Sutanto (2008) Design, Manufacture and Calibration of Sub-sonic Wind Tunnel with Open-Circuit. Journal of Mechanical Engineering CYLINDER, Vol.1 No. 1.
- Hadi Sutanto (2007) Residual Stresses on High-Speed Milling of Hardened Steel using CBN Cutting Tools. Jurnal Teknologi MEDIA TEKNIKA, Vol. 7 No. 2.
- Hadi Sutanto (2007) Experimental Study of Chip Formation on High-Speed Milling of Aluminium Alloy. Jurnal Teknik Mesin POROS. Universitas Tarumanagara.
- Hadi Sutanto (2007) Development and Application of Ceramic Tool Materials. Jurnal Sains dan Teknologi METRIS, Vol. 8 No. 2. Fakultas Teknik Unika Atma Jaya.
- Hadi Sutanto (2006) Micro-hardness Alteration on High-Speed Milling of Hardened Steel. Jurnal Sains dan Teknologi METRIS, Vol. 7 No. 4. Fakultas Teknik Unika Atma Jaya.
